BIX-L1014 Dental Headform: Chairside Training Setup Guide

BIX-L1014 Standard Headform: How to Set Up a Dental Simulation Bench

Short answer: BIX-L1014 is a standard dental headform built from a head mould, metal support rods, a base and screws. It locks onto a dental treatment table, carries a standard full-mouth dental mould, and lets the operator open the upper and lower halves and reposition the head with two regulating handles — so a dry bench can reproduce the working positions of real chairside treatment.

Key takeaways

  • Fixed, not held. Metal support rods and screws anchor the head mould to the treatment table, so it does not move while you work.
  • Two regulating handles. The rear-bottom handle sets and locks head position; the rear-top handle separates the upper and lower halves.
  • Full-mouth mould included. A standard full-mouth dental mould is supplied to simulate the oral cavity.
  • Inside and outside access. Maintenance and correction training can be carried out from both the inside and the outside of the head mould.
  • Specs to request. Package size on the product page reads "not available" and weight is unpublished — confirm both in writing before ordering.

What BIX-L1014 actually consists of

ComponentWhat it does in training
Head mouldThe working subject: a moulded head that carries the dental mould and accepts hand instruments.
Metal support rodsRigid link between the head mould and the base; keeps the head stable during procedures.
BaseMounting foot that couples the assembly to the dental treatment table.
ScrewsFixes the head mould firmly on the treatment table surface.
Rear-bottom regulating handleAdjusts and locks the position of the head mould to any working angle.
Rear-top regulating handleSeparates the upper and lower parts of the head mould.
Standard full-mouth dental mouldSimulated oral cavity for installation and procedure practice.
Published dataValue on the product page
Product modelBIX-L1014
CategoryHealthy tooth models / Oral
Package sizeNot available
WeightNot published
PriceQuoted on request

Why the headform is the part that changes training

A teaching model only transfers skill when it constrains the learner the way the real task does. In dental work the constraint is not shape recognition — it is a fixed, three-dimensional working field where the operator must hold an instrument, see an indirect view, and stay oriented inside a cavity. A model that can be picked up and turned removes exactly that constraint.

The evidence for physical models over screen-based substitutes is consistent. In a study of imaging anatomy, students working with a physical model outperformed peers who used 3D computer models and textbooks, and the authors argued that the tangible object is what drives the advantage [1]. A later teaching study reached the same practical conclusion for a spatially difficult region: combining 3D visualisation with a physical model produced better orientation than diagrams alone [2]. When 3D-printed physical models were compared directly with cadaveric material for learning external cardiac anatomy, the printed models performed comparably — showing that a well-made physical model carries real learning weight on its own [3].

BIX-L1014 applies that logic to the simulation bench: the head stays where you put it, and the supplied full-mouth mould restores the inside of the working field.

Six-step setup

  1. Anchor the base. Position the base on the treatment table and drive the screws down so the assembly cannot creep.
  2. Seat the head mould. Fit the head mould onto the metal support rods and check that it sits square to the table.
  3. Load the full-mouth dental mould. Install the standard full-mouth mould into the head mould cavity and confirm it is fully seated before any procedure.
  4. Set the working angle. Use the rear-bottom regulating handle to adjust and lock the head position for the task you are teaching — the handle allows arbitrary adjustment.
  5. Open for the lower arch. Use the rear-top regulating handle to separate the upper and lower parts of the head mould when the task is easier to reach with the halves apart.
  6. Run the drill. Have trainees work from both the inside and the outside of the head mould, then repeat the same task at a different locked angle to test transfer.

Before you order: four things to confirm

  • Package size and weight. Neither figure is published on the product page. Ask for the carton dimensions and gross weight so your lab can plan storage and freight.
  • Dental mould compatibility. Confirm whether the supplied full-mouth mould is the standard type you already use, and whether it can be replaced separately.
  • Table interface. Check the base and screw pattern against the treatment table you intend to mount it on.
  • Spares. Ask about replacement head moulds and moulds, since these are the parts that wear first in a teaching lab.

Send these questions to bomn@adabomn.com and we will answer each point and attach the current supply data.

FAQ

Q1. What is BIX-L1014?
It is a standard headform model for dental training: a head mould mounted on metal support rods, a base and screws, supplied with a standard full-mouth dental mould.

Q2. Does it come with the dental mould?
Yes. The description states that a standard full-mouth dental mould is provided to simulate installation of the oral cavity.

Q3. Can the head position be changed during a session?
Yes. A regulating handle at the rear bottom of the head mould allows the position to be adjusted and fixed at will.

Q4. Can the upper and lower halves be separated?
Yes. A regulating handle at the rear top of the head mould separates the upper and lower parts.

Q5. What training is it designed for?
Simulation of the real environment and various diagnostic procedures of comprehensive dental treatment, plus maintenance and correction training from inside and outside the head mould — used to train and test dental healthcare professionals.

Q6. How do I get the price, carton size and weight?
Email bomn@adabomn.com with the model (BIX-L1014), the quantity you need and your destination port. The sales team will return the quotation, package size and gross weight.

Request a quotation

Write to bomn@adabomn.com for current pricing on BIX-L1014 and for the carton dimensions and gross weight, which are not published on the product page. If your programme also covers tooth morphology and restorative procedures, ask for the healthy tooth model range in the same enquiry and we will quote it together with the headform.

References

  1. "Let's get physical": advantages of a physical model over 3D computer models and textbooks in learning imaging anatomy. Anatomical Sciences Education. 2013.
  2. Teaching Pterygopalatine Fossa Anatomy Using 3D Images and Physical Model: A Novel Teaching Strategy. Medical Science Educator. 2024.
  3. Use of 3D printed models in medical education: a randomized control trial comparing 3D prints versus cadaveric materials for learning external cardiac anatomy. Anatomical Sciences Education. 2016.